To be honest, what I fear most during the installation stage is not the gap!

In the installation stage, every time I punch the hole, I am frightened.

The installation stage was very smooth, and no worries occurred. It was not that I knew how to decorate, but that I did not lay the \”foreshadowing\” in the early stage.

However, many homeowners are not so lucky. When installing a bathroom cabinet, showerhead or skirting line, it will directly hit the water pipe. Not only will the wall be damaged, but there will be a risk of water leakage in the later stage, and the maintenance is also very cumbersome.

In the installation stage, a rollover accident that breaks the water pipe or wires can actually be avoided.

In this issue, let\’s talk to you about the skills of avoiding the installation of water pipes and wires, which fundamentally solves the problem of repairing before decoration.

0 1

This kind of pit is too common

In the installation stage, we can use the to break the water pipe or wire. There are too many cases of overturning.

HomeownerRay Sheep Sheep, interrupts the cold water pipe when installing the bathroom cabinet.

Finally, this repair method is really unreliable, and it will definitely leak in no time.

And that is, why are there no spacing between hot and cold water pipes?

The owner DAD\’s home, the last step of hard decoration, interrupted the wires when installing the skirting line. Fortunately, the on-site supervisor would have been tricked.

Even, there are those who install TVs to interrupt wires, which are becoming more and more outrageous.

What is even more outrageous is that when installing kitchen wall cabinets, you can break the water pipes.

In short, there are many cases of interrupting wires and water pipes. When installing bathroom cabinets, showers, skirting boards, TVs, electric water heaters, gas water heaters, hanging cabinets, etc., you must pay attention to avoid trouble.

0 2

How to fix it if interrupted?

How should the water pipe and wire be repaired when broken? It must be repaired. Different repair methods have different durability.

①、电线修复。 In order to avoid leakage or stranding of broken wires, it is best to replace the wires instead of using electric tape to wrap the connectors.

Wrap the connector also has the risk of leakage or disconnection, and it is difficult to pull the old wire during later maintenance.

When replacing wires, three types of wires of different colors are involved. It is recommended to purchase wires of the same specifications according to the number of meters to avoid waste when buying the whole circle.

②, Water pipe repair. When installing, drill holes and break the water pipes, there are two ways to repair them:

1. Use glue to plug it. Put the holes in the water pipe with glue to repair them. This repair method is simple and easy to operate and does not damage other places. However, the durability is not high and the risk of water leakage in the later stage is very high.

2. Hot melt welding.Reheat melt welding of water pipes is the most reliable repair method. However, holes need to be expanded, and the walls will be dismantled on a large scale.

In short, repairing after being interrupted is extremely troublesome, and you must avoid it when installing.

<p

0 3

How to avoid it?

Drive holes and breakages of water pipes or wires during the installation phase. See the following methods for specific operations:

①. Make a good line marking.After laying the tiles, marking them according to the direction of the line in time. This is the best way to avoid drilling holes and breaking water pipes or wires.

Because the plumbers and power workers are most clear about the direction of the line, this work is completed by water and electricity. If no marking is made, the water and electricity should be repaired by water and electricity.

②. Do not open horizontal grooves.

When transforming water and electricity, you must avoid the generation of horizontal grooves. This is not only unfavorable to predict the direction of the line, but also forms horizontal cutting on the wall, which has a greater degree of damage.

③. Take photos of the line.

Preparation of the line, using the line photos during installation can also avoid the embarrassment of drilling holes to get the line.

However, the way of using mobile phones to keep photos is lagging behind. Now it is more about shooting the line direction into VR, and the more intuitive retention line direction is retained.

The above three methods can avoid drilling holes and getting the line. However, you still need to check before punching the holes and do not blindly construct.

0 4

Repair skills

After drilling holes and getting the water and electricity lines, not only the lines need to be repaired, but the wall also needs to be repaired. How to repair the tiles?

<img src=\"https://www.toutiao.com/a7477302863941747250/data:image/gif;base64,R0lGODlhAQABAIAAAAAAAAAAAP///yH5BAEAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA

After fixing, no difference was seen at all, this is the best result.

In short, it is very common to drill holes during installation to get water and electricity lines, but it is also an avoidable thing.

When water and electricity transformation, we must avoid the generation of horizontal troughs and also make water and electricity marks; before installation, we must determine the direction of the line and then construct to avoid blindness.