How to use deepseek to solve the problem of flip-flop car door deviation?

How to use deepseek to solve the problem of deviation in the flip-board car door?

On the morning of February 25, the new media editor of Kunming Haiton Car Door used deepseek deep thinking, Wen Xinyiyan and Doubao AI to answer \”Analysis and solution for the reason why the flip-flop car dodge deviation\” at the same time. The results can be seen that deepseek and Doubao AI have similar answers, but the solution provided by Wen Xinyiyan is more in line with common faults in real life, and its solution is also more operational.

Let\’s first look at deepseek\’s answer. It says that the deviation of the flip-flop door may refer to the door slightly deviating from the track when rising or falling, or the two sides are out of sync. This is defined in the phenomenon of deviating the vehicle door. During the actual use process, the biggest failure of deviating the vehicle door is actually a gap that appears on one side of the contact part of the bottom of the rear door panel and the ground. And this key information has not been recorded by artificial intelligence yet.

After defining what is the phenomenon of a deviant vehicle door, deepseek\’s answer was also unlogical. It says, first of all, what are the possible reasons? I have to think about it one by one. Problems in the tract, such as the tract being loose or deformed, there are strange objects in the tract, or they are not installed level. Then there is the problem with the spring system. Uneven spring force will lead to unbalanced forces on both sides, which will lead to deviation. Problems with rollers and bearings, such as rollers wear, deformation or jamming, or lack of slippage. The chain or door plate is deformed, and the door plate may be deformed due to aging of the material or impact of external forces. Installation problems, such as the unbalanced track during initial installation, or the door itself is unbalanced. For motors and transmission systems, if it is a motor door, the motor output is out of synchronization or the transmission parts are worn.

Next to solve the problem. Check the track to ensure that the safety is securely installed, clean the anomalies, and adjust the level. Adjusting the spring force may require professional operation. Check the rollers, replace the damaged rollers, and lift the sliding bearings. Check the door panels and chains, correct or change the deformation parts. Recalibrate the door balance and may require adjustment of the spring or duct. Check motors and transmission systems, adjust synchronization, and replace wear components.

The answer to Doubao AI can be used as a technical extension of deepseek or an operational technical guide. For example, the problem of the track: When installing the track, if the track is not sure that the track is at a horizontal state, the door will be affected by gravity and the slant of the track during operation, resulting in a deviation. After long-term use, the duct may deform or damage due to external force collision, rotten or material aging, resulting in the door not being able to move along the normal duct during operation.

Door balance misalignment: There is a problem with the balance system of the door,If the spring is uneven in elastic force or the chain is loose, it will cause the door to be uneven in force when moving up and down, resulting in deviation. Due to external force collision, long-term storm or moisture, the door may deform, causing the coordination between the door and the track to deviate.

For light and slightly deformed tracks, tools can be used to correct them; if the tracks are damaged and severe, new tracks should be replaced in time. Check the state of the spring and chain, adjust the spring\’s elastic force to make it evenly bear the force; if the chain is loose, the looseness of the chain should be adjusted appropriately. For small-deformed doors, you can try to correct them with tools; if the shape is severe, it is recommended to contact professionals to repair or change the door.

The main reason why Wen Xinyiyan\’s answer is more in line with the needs of end users is that it can directly solve the pain and difficulties of user self-examination and self-study. For example, it says that when the flip-flop car door appears slightly off, you can first observe whether the steel wire is loose. The method of judging the loosening of the steel wire rope is also very simple. First, turn the door open once, observe whether there are any excess parts of the steel wire rope under the opening state, and then adjust the length of the bottom bracket screw on one side to loosen. The loose wire may cause light and slightly loose due to long-term use or improper operation. This looseness will cause the tension on both sides of the door to be unbalanced, resulting in a light and slightly tilted slant during door operation.

The second is the hearing of the sound to distinguish the strength of the torsion spring. If the operation noise has become louder recently, the door has slightly deviated, but the steel wire does not show any looseness, which may be caused by the weakening of the torsion spring. The torsion spring force of the flip-flop car door will gradually weaken with the extension of the use time. If the torsion spring force is insufficient, noise may occur during operation, and light and slight slanting will occur during operation. If you do not want to purchase the adjustable bottom bracket of the Hiton Car Door for correction,Use a homemade small spring to make the deviation. The editor of the small spring homemade tutorial has been shared on the new media platform many times. Friends in need can view it by searching the keyword \”Homemade kitchen door spring\” online, or use AI to search.

The end is to adjust the floor of the vehicle warehouse after the decoration is completed, such as building basic facilities such as tiles, floor paint, and waterproofing, which will cause uneven ground, so light transmission will still appear after closing. This does not mean that the warehouse door is offside. Users need to re-adjust the limits of the warehouse door, so that the bottom strip at the bottom of the door can be reduced by several millimeters to eliminate the light transmission problem. If the warehouse has a tiled wall that is high on the floor where the door is located, it may also cause the door to appear when it closes, indicating that it is slightly off.

In general, there is a phenomenon of light deviation in the warehouse, which shows that there is a small gap on the bottom side after the door, which can be corrected by self-examination and self-study.

Adjust the steel wire rope: For the situation where the steel wire rope is loose, the two sides can be balanced by re-adjusting the steel wire rope to ensure that the overall door panel remains flat.

Reinforcement accessories: Check whether the accessories such as chains, joints, quiet wheels, small tamps are loose, and reinforce them to ensure the stability of the warehouse hardware accessories.

Adjust the torsion spring force: If the torsion spring force is weakened, the torsion spring can be adjusted to restore the normal operating state of the door. This usually requires a professional to operate.

Homemade spring micro-tuning: Make a spring micro-tuning on the bottom wheel rod of the trunk at the side of the vehicle. When making, first roll the wire through the rod, then double-width to make a spring, adjust the number of springs according to the size of the gap until the gap is filled. This method is suitable for slightly off-straight.

Uneven floor: If the uneven floor causes the door to appear when the door is closed, you can solve the problem by adjusting the limits of the warehouse door, or changing the floor construction or adjusting the installation location of the warehouse door.

Kunming Haiton Car Door Editor\’s Warm Tips, it is recommended that users pay attention to the maintenance and maintenance of the car door. Regular maintenance and maintenance of the car door, including checking the wear of steel wire, guides, brackets and other accessories, and changing damaged accessories in time, adding lubricating oil, etc., can prolong the life of the car door and reduce the occurrence of deviation.