House decoration, 8 things that workers will never do, each of which affects the quality of the project.

Decoration is a complex system project, and almost all the pitfalls are due to details.

During the entire decoration process, details are an important factor in determining the quality of construction. It will affect the quality, and even affect the appearance and life after moving in.

Whether it is full, half-pack, or clear bag, it means that you can be a hand-off manager, let go completely and ignore it.

In fact, when looking for a decoration company, you must pay more attention to details, otherwise you will be fooled immediately and spend more money and you will not get the desired effect.

This issue will talk to you about the details that need attention but are rarely mentioned in daily life. You must explain it to the construction master clearly.

When removing walls, you need to bounce the line

Demolition of walls is a matter of no technical content, but it does not mean that just swing a hammer and smash it. There are many details that need to be paid attention to.

In addition to not being able to be removed to load-bearing walls and structural walls, you should also pay attention to: be sure to stretch the line when demolishing the walls.

Before construction begins, the line is first bounced and then construction is carried out according to the predetermined demolition size. If only part of the area is removed on a wall,The details must be done.

▲没有弹线，墙口不整齐

Otherwise, the later stage will be a messy wall, which not only does not match the size, but also requires secondary vigorous repair, which is also a considerable expense.

▲After the thread is bounced, the cutting is completed and then dismantled, and the wall will be more neat.

When after the thread is stretched, the wall is particularly neat, the size is more accurate, and the workload is required in the later stage is smaller.

If you don\’t brief them in advance, the construction master will definitely not pay attention to it.

▶Water and electricity pipeline protection

After the water and electricity are over, the ground is full of messy pipelines. When the tiler enters the site, there are a lot of carts and tiles entering the house, which will cause damage to the pipeline.

<img src=\"https://www.toutiao.com/a7476902531218719286/data:image/gif;base64,R0lGODlhAQABAIAAAAAAAAAAAAP///yH5BAEAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA

Therefore, after the water and electricity are over, the water and electricity workers must use mortar to protect the pipeline.

Actually inconspicuous details, but if you don\’t say it, the other party will definitely not do it.

When doing protection, there is no need to do the whole house, but to protect the carts where the cart can press.

The correct step is to conduct a compression test first, and then carry out protection operations after normal pressure and ensure no leakage.

▶ Do cleaning before brushing waterproof

Before brushing waterproof, be sure to clean the ground, which is the basic process of waterproof.

▲After thoroughly cleaning, the ground must be wet.

At the same time, the leak must be plugged in advance with the water pipes, the holes on the wall and the corners, and then the waterproofing must be applied.

The probability of water leakage after check-in becomes higher.

Hold early. It is recommended that you prepare a broom, garbage shovel and leak plug before applying waterproofing. The construction personnel are required to clean thoroughly first, then use leak plug-in to treat the water pipes and holes, and finally apply waterproofing.

▶ Stainless steel nails for woodworking

When the carpenter enters the site, it mainly involves the suspended ceiling and various shapes of the home.

▲The ceiling is rusted and yellowed.

When carpentry ceiling, it is best to use stainless steel nails to avoid rusting the nails after moving in, resulting in yellowing of the ceiling.

▲Use anti-rust paint on the ceiling nail hole

Or, you can use ordinary nails and then apply anti-rust paint on the nail hole.

It is recommended to use stainless steel nails throughout the house to completely avoid the problem of rust by self-tapping screws.

▶ Only when the putty is dry can it be scraped for the second time

The oil workers enter the site, the main processes involved are scraping putty and brushing latex paint.

Putting is the base layer of latex paint, and good putty is the guarantee of the quality of latex paint painting. When scraping putty, the most common problem is that there is no interval between the first and second passes.

▲The putty layer is cracked

This is not possible. The probability of cracking in the later stage is very high, especially in places where putty is thicker.

It is recommended to stay early. The first putty is completed. You must wait until it is completely dry before the second construction can be carried out, otherwise it will be a pit.

In addition to scraping putty, the same is true for brushing latex paint. You must wait until the first time is completely dry before the second time is applied.

▶ Single bag of bathroom door

Single bag of bathroom door or double bag, has a significant impact on the space.

▲Double bag of bathroom door cover

Double bags means that door covers both inside and outside the bathroom door, and no corners are needed when applying ceramic tiles.

▲Bathroom door case

Single bag means that one side of the bathroom door is covered with a door cover, and the other side requires an open angle of the male corner.

<img src=\"https://www.toutiao.com/a7476902531218719286/data:image/gif;base64,R0lGODlhAQABAIAAAAAAAAAAP///yH5BAEAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA

When the tiler enters the site, the series must be briefed, otherwise the master will carry double-pack construction, and the door covers must be included inside and outside in the later stage, otherwise it will be ugly.

▲The drawer of the washbasin fights with the door cover and cannot be fully opened.

It is recommended to have a single bag in the bathroom door, and select the position of the door cover according to the position of the washbasin.

The washbasin should be opposite to the door cover, that is, the washbasin is outside, and the door is inside, otherwise it will be the other way around. With this design, the drawer of the washbasin will not \”fight\” with the door cover.